• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. rtaylor

    Sanding questions

    If the ring is drum sanded on both sides why is it necessary to sand again with a board?? I have made a lot of vases and never done that. The rings are always parallel to each face and true to glue on. Works perfectly, What am I missing here?
  2. rtaylor

    Indian Blanket sawing

    Thanks Lloyd, no magic solutions I guess. That seems the best for me too. A little bit of saw kerf from chatter can really mess up this laminate glue up.
  3. rtaylor

    Indian Blanket sawing

    I have a question about ripping the narrow (1/8) strips from the chevron when constructing the Indian Blanket feature segments. in order to get the cleanest kerf free slices. I have tried both setting the fence at 1/8" and using a Microjig push block with a 1/16 attachment. I have also used a...
  4. rtaylor

    Line Laser

    Thanks Mark, I am familiar with that post. I followed it years ago too. The laser dot is not the same as a line laser that actually shows where the blade will cut in a straight line. All my glue up stuff is patterned after Lloyds ideas. The dot, although good, leaves a little to be desired.
  5. rtaylor

    Line Laser

    Has anyone incorporated a line laser with their saw into 2nd and 3rd generation cutting using LamPro? What do you do? Thinking about trying one.
  6. rtaylor

    Comment by 'rtaylor' in media '20221114_170615.jpg'

    Hmmmm??
    • rtaylor
    • Gallery comment
  7. rtaylor

    Comment by 'rtaylor' in media '20221114_170615.jpg'

    I too would love to see the procedure for this turning. Amazing piece!!
    • rtaylor
    • Gallery comment
  8. rtaylor

    Woodturner Pro

    As long as Woodturner Pro has been out.....this seems really strange. Some of the rings are OK then some are off by a lot. Could windows 10 have something to do with it?
  9. rtaylor

    Woodturner Pro

    Has anyone had issues with the calculations being inaccurate for segment rings using Woodturner Pro? I am having real issues. I am using 1/16 accuracy. My ring is 16 segments. Board width 7/8", segment edge length 1", Inside edge 5/8". all dimensions are spot on. Using a wedgie sled so the ring...
  10. rtaylor

    Row Thickness

    Is there a way to change individual row thickness in Segment Pro, or are do they all need to be the same? I want to do a feature ring that is painted. Thinner rings allow more detail to paint. Maybe this is coming in a later version. I am not seeing any way to adjust individual row thickness...
  11. rtaylor

    glueing thin rings

    OK thanks for the help. I think that sounds like a good way to do it.
  12. rtaylor

    glueing thin rings

    Thanks for the reply. Do you just use tape to hold the half rings until dry or just press the segments together and flatten them with weight. I am going to give this a try.
  13. rtaylor

    glueing thin rings

    What is the best way to glue thin rings together and keep them flat? For thicker rings I use blue tape and then clamp with a band clamp then drum sand them flat. I am having trouble with the thinner rings. My feature ring needs to have about 10 rows of 1/8 inch thick rings. They are stacked and...
  14. rtaylor

    Feature ring construction

    Thanks...I like the looks of that over what I have been using
  15. rtaylor

    Feature ring construction

    Thanks for the advice Lloyd. Just to be clear you are using a frame to glue the chevrons so that the points are in exact line. Then you use the Dubby with a laser to cut the second generation. At this point you glue just the repeating units separately, square them up and angle cut them for a...
  16. rtaylor

    Feature ring construction

  17. rtaylor

    Feature ring construction

    I need some advice on construction of, and, cutting segments for a feature ring. Although I have done this lamination before, I think I am making it more difficult than it needs to be so I thought I would ask how some of you do it. I use a Dubby sled for cutting segments and have found it to be...
  18. rtaylor

    Lamination Pro

    I have now, thanks. I am not on site as often as some of you are..... so I miss lots of stuff:oops:
  19. rtaylor

    Lamination Pro

    After uploading and installing the new version 3 I am not seeing the saw kerf tool in the tool bar. I also do not get to set my clipping region, nothing shown there. These features are shown in the software help files???? I am running windows 10. Any help would be appreciated.
  20. rtaylor

    Cutting first generation lamination question..

    Why is it necessary to cut through the middle of the lamination on this type of design? The repeating unit is 2 strips and it is one generation. Would it not be easier to just cut them apart on the glue line? Is the program showing this as though it is going to go another generation or is it...
Back
Top