• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. Wayne Miller

    5 pointed stars using Lamination Pro?

    I have never been good with LamPro so I ask you. Can you design a 6 pointed star, Please.
  2. Wayne Miller

    Floating bottom for urn

    I often use a floating bottom and then finish the top using a vacuum chuck. If you make the floating disk perfectly flat and the recess flat it will hold the full vacuum my pump will produce. I suspect this is good enough for dust (ash).
  3. Wayne Miller

    Comment by 'Wayne Miller' in media 'P2-Z2SML.jpg'

    Actually it was paart of the Holiday Swap in the Segmenting Chapter. He now lives in KY.
  4. P2-Z2SML.jpg

    P2-Z2SML.jpg

    Acrylic segments. 5.5" tall.
    • Wayne Miller
    • Media item
    • Comments: 2
    • Category: Segmented Sculptures
  5. Wayne Miller

    Question about WTP

    Jim is working one of my designs. It is my donut vase which I have made about 30 times so I know how it should work. I have done this demo both at AAW andd Segment Sympoia. He also asked me if I could seee an issue. I sent him my WRPro dims. I'm glad to see a resolution. While being exact to 3...
  6. Android.JPG

    Android.JPG

    Android Logo. 8" tall, 7" outsdide the arms. Custom Specctraply alll one color (Lime Green).
    • Wayne Miller
    • Media item
    • Comments: 1
    • Category: Segmented Turnings
  7. Wayne Miller

    Anyway to use a iPad

    I just went to the app store for Apple and did a search for Microsoft. All the apps are there. I don't know where you are looking, but try again. Wayne
  8. Wayne Miller

    Anyway to use a iPad

    As of several months ago there is a full version of all the MS Office products (Word, PowerPoint, Excel) available as free downloads from the ITunes Store. You can import files into them from the iTunes file sharing section. If you have Office 365 you can register your iPad (you get 5 device...
  9. Wayne Miller

    Anyway to use a iPad

    If you do the math yourself in Excel you can import that into your iPad. there is software that uses Excel and can save as xlsx.
  10. Wayne Miller

    Need help to make thoughs "feathers" for a segmented vase

    At my website www.pzturn.com go to the links tab. there is a pdf document describing how to make feature rings. Feathers/arrows are described there. Actually, that is about the easiest design to make. Also, I think it is in the first Malcolm Tibbetts book or dvd. Wayne
  11. Wayne Miller

    Lamination PRO Tutorials - Multi-Generation Laminations

    Before you start building you should look on this Forum. there is a thread on multi-gen cutting. At Bodwell shows pictures of his clamping fixture which has some different features from how Lloyd does it. For me it works better. Either way will work just a matter of having a permanent setup or...
  12. Wayne Miller

    Digital Thin Rip Jig for Table Saw

    The stock to be cut is placed between your fence and the roller bearing which is set to the desired cut width. After making the cut you move the fence to bring the stock up to the bearing again without moving the setup. Then make repetitive cuts as needed. Actually quite simple once you...
  13. Wayne Miller

    Transition zig zag bowl

    If you decide to use Inlace be very careful. It comes with a warning to use it in well ventilated areas. They really mean it. Whenever I use it now I mix it and keep the piece outside until it cures. I have multiple externally vented air cleaners in my shop but they cannot do much for the...
  14. Indian Blanket

    Indian Blanket

    I finally finished a turning using the "trial" Indian Blanket. It is made of Hard Maple and Bloodwood. It is 7.5" D. and 6" H. I decided to make the star top using the Kevin Neely method. As usual I learned a great deal. It looks pretty good but the next one will be better...
    • Wayne Miller
    • Media item
    • Comments: 3
    • Category: Segmented Turnings
  15. Wayne Miller

    Concentric rings

    I have not found a way. When I design a "Keeper Ring" for a floating base I just decide upon an OD and an ID and make it as a separate 1 layer project. This might be tedious for what you want. Just curious, when you do this do you brick lay the rings, if not, you could just construct them from a...
  16. Wayne Miller

    Will this work?

    I have had a plan for a 3 tired unit for holding finger pastries. I once made a flat platter with a plug which literally blew up. Since then I have made all of my pieces with a floating bottom. I have since thought of several ways to make the middle but none of them seemed aesthetically...
  17. Wayne Miller

    Transition zig zag bowl

    I once had a cross grain turning self destruct. Ever since then I have not tried anything like this. Many people do this on a regular basis with no problem. Mesquite is so stable that you have chosen something favorable to a good result. I do like the way it looks. Wayne
  18. Wayne Miller

    Transition zig zag bowl

    Same with me. Please post the picture to the Gallery.
  19. Wayne Miller

    Version 3 Lamination PRO Update - Southwest Design View.

    Finished Ring For those of you who have been following this thread. I started out trying to make an Indian Blanket design. I made many mistakes along the way. I misunderstood the cut dimension, had some clamping issues, had an old version of the software which gave me a wrong calculation of...
  20. Wayne Miller

    2nd generation saw cuts

    Thanks Lloyd, I could not open Art's pictures yesterday before I wrote. Now I have opened them and see what he did. I had thought of that as well but I had the table and didn't want to take the time to build something. Wayne
Back
Top