• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. jwmadzelan

    Latest segmented vessel

    nice
  2. jwmadzelan

    Steps to produce a basic segmented vase

    great presentation. Thank you
  3. jwmadzelan

    Determining angles of rings

    great idea. Please keep us updated on any progress you make.
  4. jwmadzelan

    Beginner's Project - Open Segment Christmas Ornament

    Great job thanks. I would like to see some actual turning of the globe.:)
  5. jwmadzelan

    download versions

    thanks. just wanted to find out if I was doing something wrong.
  6. jwmadzelan

    download versions

    When I go to the download page I have two questions. 1. When I download and install lamination pro 3.02.016 and run the program it shows build 3.2.014. I have done this several times and get the same results. I have search for two installation on my win10 computer, but could only find one. Any...
  7. jwmadzelan

    Alternative to Sprinkler?

    Good job. Love the pictures on how to do the job. Sometimes I have a hard time picturing when something is just explained
  8. jwmadzelan

    Remove Old Threads

    I agree, I thing they should be archived and be found in 'search' if needed.
  9. jwmadzelan

    Splitting Rings With A Bandsaw

    looks good. I am going to make one to help with my dizzy bowls.
  10. jwmadzelan

    New Style for Forum under test - please comment.

    I like the new size. Have old eyes and had a hard time reading.
  11. jwmadzelan

    Open-Segment Bowl - Petal

    I saved your plan and renamed it "hope to be able to do someday". Thanks
  12. jwmadzelan

    Identify wood type

    That looks really good. I can hardly wait for the upgrade
  13. jwmadzelan

    First segmented vessel

    nicely done
  14. jwmadzelan

    My steps to make a Bowl from a board

    Thanks. What I like about wood turning is I see something that looks neat and then I try to figure out how I can make it. I have not updated my web pages in years as I have forgotten how to do it. I think it is time to relearn to update.
  15. jwmadzelan

    My steps to make a Bowl from a board

    I cut and sanded the inside of the bowl as I stacked the rings on the lathe. This make it easier to get the inside done. It was a fun project.
  16. jwmadzelan

    My steps to make a Bowl from a board

    Next I glued the 4 sheets of wood together to form another board. Note: I cut the slices so I could start the twist pattern of the bowl before I cut the rings. This makes each ring I cut on the ring master look like 4 rings, and make the pattern blend better. I then cut the circles with the...
  17. jwmadzelan

    My steps to make a Bowl from a board

    Next I cut the board onto 1/8 inch slices on my band saw. I made the slices a smidge larger than 1/8th so I could sand the cut side flat. I also flattened the cut side of the board to insure everything remaining square.
  18. jwmadzelan

    My steps to make a Bowl from a board

    I tried making a bowl from a board using my small band saw. While the bowl design turned out well when I finished it, my cuts on the band saw were not precise, and I had a lot of really thin spots that were a distraction. I have a ring master that I have not used in a long time, so I tuned it...
  19. jwmadzelan

    Miter crosscut sled

    I used the Incra Miter express for years also. About six months ago I built the wedgie sled and bought the wedgies. I have not had to sand my segments after I started using the system.
  20. jwmadzelan

    New web site

    I was a little apprehensive when you started our new web site. I had learned to find what I wanted on the old one. But the new one is really good and getting better. Really like all your new features and layout.
Back
Top