• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. D

    Off Center

    I 3d print my own segmenting plates. I can use any gap angle and any number of segments within reason. Even 3D printers have limitations. The largest plate I can print is 10 inches. I'm sure Jerry Bennet picked a limited number of options so selling plates didn't become unmanageable. I also use...
  2. D

    Segeasy Plate

    The measurements I made on the 48-2 plate that I bought are shown in the excel sheet that I posted in this thread. The variation that I measured is close to what Jerry posted as a measurement of the radius of the ring. It is worth noting that the largest errors are across the diameter from each...
  3. D

    Segeasy Plate

    This is an open segment plate. The tolerance of this plate is so bad that it is basically unusable. If you can supply one with better tolerance I would like to exchange the plate. If not I would like to return it for a refund.
  4. D

    Segeasy Plate

    I did take a measurement then remove the wedge and then put it back in the slot. I did get the same measurement. Just for reference I am a retired Industrial Instrument Technician. I spent years measuring things and setting up Instrument calibrations. I was very careful taking the measurements...
  5. D

    Segeasy Plate

    The segment has no fuzzies. The segment was oriented the same for each measurement. I took my measurement with the rod on the caliper placed against the edge of the left side of the wedge slot. I placed the wedge loosely in the slot and extended rod of the caliper. I then used the pressure that...
  6. D

    Segeasy Plate

    The measurements for the spread sheet were made using the same segment moved from position to position and measuring from the outside of the plate to the outside of the segment. My thinking is that if a single segment doesn't position at the same distance from either the center or the outside...
  7. D

    Segeasy Plate

    Attached is an Excel Spreadsheet Showing the actual shape of the outside radius using a single segment moved and measured from the outside diameter in each position on the Segeasy plate. The measurements were taken using a digital caliper. I created a radar chart to graphically show what I was...
  8. D

    Segeasy Plate

    I recently purchased a 48 segment Segeasy Plate for use with the Stomper. When I place my segments on the plate I get an oval shaped ring instead of round. I have tried moving the segments around on the plate to see if it had something to do with the S.E.L. of my segments and I found a couple of...
  9. 20230418_112314.jpg

    20230418_112314.jpg

    D. Lewis Flower Bowl. It is 12 5/8' in diameter and 6 1/2" tall. It is constructed of 10 different wood species. (Padauk, Hard Maple, Purple Heart, Jatoba, Jarrah, Zebra Wood, Yellow Heart, Canary Wood, Lyptus, and Sepele) There are 585 individual pieces of wood. It is finished with Lacquer.
    • Donald Lewis
    • Media item
    • Comments: 2
    • Category: Open Segment Turnings
  10. 20230418_112343.jpg

    20230418_112343.jpg

    D. Lewis Flower Bowl. It is 12 5/8' in diameter and 6 1/2" tall. It is constructed of 10 different wood species. (Padauk, Hard Maple, Purple Heart, Jatoba, Jarrah, Zebra Wood, Yellow Heart, Canary Wood, Lyptus, and Sepele) There are 585 individual pieces of wood. It is finished with Lacquer.
    • Donald Lewis
    • Media item
    • Comments: 0
    • Category: Open Segment Turnings
  11. D

    Is the Ring View backwards?

    I want to apologize for my comments. They came out of frustration from what I have run into as a new user. I would like to offer up another solution to the screen print discussion. Windows 10 and 11 have a Snip tool that basically allows you to copy any portion of a screen instead of printing...
  12. D

    Is the Ring View backwards?

    Good morning Loyd. In response to your reply. The suggestions that I made were out of frustration with things that I ran into using your software. All of the Items as additions or fixes that I suggested were brought up as problems and work arounds were discussed in your forum by other users. I...
  13. D

    Is the Ring View backwards?

  14. D

    Is the Ring View backwards?

    My comment about the application not having the necessary features comes from two points that have come up in this thread. First, when someone thought the ring view was backward, which it is if you use a platform to assemble your project I suggested that a toggle function be added to the...
  15. D

    Is the Ring View backwards?

    You would think that an application would have the necessary features without having workarounds to get the job done!
  16. D

    Is the Ring View backwards?

    Would it be possible to add a print function to the Paint view. I don't have a computer in my shop as I'm sure many of us don't. It would be nice to be able to take a printed image of either the Paint Screen or the Rings .pdf to work off of depending on the assembly method being used. I happen...
  17. D

    Is the Ring View backwards?

    Just a note that might be worth considering. If you build a bowl upside down like you would if you are using Segeasy Plates and the Stomper the Ring View is correct. If you are building a bowl from the bottom up like you would on a Chefware EZ segment jig or other platform it is backwards. If it...
  18. D

    Chatter/vibration turning bowl lip

    I recently bought a CNC cut steady rest off of Etsy. Works great and a lot less expensive than the ones mentioned in earlier posts.
  19. First Open Segmented Turning

    First Open Segmented Turning

    Bowl designed in Segment Pro. Woods are Jatoba, Padauk, Canary, Yellowheart and Ebony. The dimensions are 6" tall and 11.5" in diameter.
    • Donald Lewis
    • Media item
    • Comments: 0
    • Category: Open Segment Turnings
  20. First Open Segmented Turning

    First Open Segmented Turning

    Bowl designed in Segment Pro. Woods are Jatoba, Padauk, Canary, Yellowheart and Ebony. The dimensions are 6" tall and 11.5" in diameter.
    • Donald Lewis
    • Media item
    • Comments: 0
    • Category: Open Segment Turnings
Back
Top