• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

My steps to make a Bowl from a board

jwmadzelan

PRO Member
I tried making a bowl from a board using my small band saw. While the bowl design turned out well when I finished it, my cuts on the band saw were not precise, and I had a lot of really thin spots that were a distraction.

I have a ring master that I have not used in a long time, so I tuned it up to make a bowl using it.

I cut strips of different woods and glued them together to make a 10 x 10 x 1 ½ inch board of different colors. Then squared it.

making a dizzy bowl 1.JPG making a dizzy bowl 2.JPG making a dizzy bowl 3.JPG making a dizzy bowl 4.JPG making a dizzy bowl 5.JPG making a dizzy bowl 1.JPG making a dizzy bowl 2.JPG making a dizzy bowl 3.JPG making a dizzy bowl 4.JPG making a dizzy bowl 5.JPG
 
Next I cut the board onto 1/8 inch slices on my band saw. I made the slices a smidge larger than 1/8th so I could sand the cut side flat. I also flattened the cut side of the board to insure everything remaining square.


making a dizzy bowl 6.JPG making a dizzy bowl 7.JPG
 
Next I glued the 4 sheets of wood together to form another board.

Note: I cut the slices so I could start the twist pattern of the bowl before I cut the rings. This makes each ring I cut on the ring master look like 4 rings, and make the pattern blend better.

I then cut the circles with the ring master.

making a dizzy bowl 8.JPG making a dizzy bowl 9.JPG making a dizzy bowl 10.JPG making a dizzy bowl 11.JPG
 
I cut and sanded the inside of the bowl as I stacked the rings on the lathe. This make it easier to get the inside done. It was a fun project.
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image002.jpg
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image004.jpg
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image006.jpg
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image008.jpg
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image010.jpg
C:\Users\woodm\AppData\Local\Temp\msohtmlclip1\01\clip_image012.jpg


making a dizzy bowl 12.JPG making a dizzy bowl 13.JPG making a dizzy bowl 14.JPG making a dizzy bowl 16.JPG making a dizzy bowl 17.JPG making a dizzy bowl 18.JPG
 
Nice project Jon. It's always interesting to see how different folks come up with different methods but end up with the same results. I recently completed my "Vase from a Board" which was my first attempt at this technique, won't be my last.

I had a look around your website as well, you do a wide variety of work. Nice stuff.
 
Jon, thanks for posting the steps you took. I enjoy seeing the different ways taken to construct a beautiful bowl like thisl
 
Thanks. What I like about wood turning is I see something that looks neat and then I try to figure out how I can make it. I have not updated my web pages in years as I have forgotten how to do it. I think it is time to relearn to update.
 
I have a foolish question, can I use segmented pro, or Woodturner Pro to get measurements for economy bowls, or bowls from boards? Thank you in advance.
 
Back
Top