• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. J

    Hi from SC

    Hi Elizabeth: Welcome ............. I've been a member about a year. find this sight very helpful. Also usually any question you might have gets an answer rsther quickly.
  2. osage orange

    osage orange

    bowl is about 10 inchs wide & 4 inches deep
    • justover7
    • Media item
    • Comments: 0
    • Category: Bowl From A Board
  3. stave and spalted maple vase

    stave and spalted maple vase

    • justover7
    • Media item
    • Comments: 0
    • Category: Member Galleries
  4. J

    Cutting narrow laminate strips......

    I purchased a thin rip guage from rockler & I have used to cut 1/8 spacer stips: it work very good. However I haven't tried it yet on a lamination.............
  5. J

    3rd generation question

    No After I made 2nd gen I just eyeballed & cut segments. However; I had to scrap the 3 rd gen I made a error & will not have enough segment material. I'm going to try & maake a small 2nd gen cutting board out of remaining material.
  6. J

    3rd generation question

    When I did the 2nd gen I just eyeballed the segments I guess I could do the same on this one.
  7. J

    3rd generation question

    Hello........... I'm attempting another travel mug; this time with 3rd gen. feature ring. My plan is to cut the second gen with a compound cut to form a 3rd gen. seg. My question is; do I need to try to cut the 2nd gen laminate as to hit the imaginary center of the rdu in the center of the...
  8. J

    couple of questions

    Also Loyd if you're ever in our area, a friend of mine owns Twinn Oaks Bluegrass Park; I actually helped him build a lot of it.
  9. J

    couple of questions

    Good morning all Where do most of you folks get your wood from I would like to compare prices? Does any members live anywhere close to me; I live in S GA about 70 miles N of Jacksonville FL? By the way Loyd I saw that you played banjo; about 30 yrs ago I got somewhat decent on a fiddle...
  10. J

    New Member from Alberta, Canada!

    Welcome AL As stated above a good place to ask questions. You will ssurely get you're money's worth here.
  11. coffee_mug

    coffee_mug

    • justover7
    • Media item
    • Comments: 0
    • Category: Multi-Generation Laminatons
  12. J

    2nd gen coffe mug

    here's my first succesfull 2nd gen feature ring............
  13. J

    cancer awareness ribbon feature ring

    Hi John: the vase is over at my gym now can't get another pic. the way I did the portholes is:I had a guy engrave ribbons on walnut 1/8 deep. I then mixed red & white inlace & poured the ribbon . I made a cartwheel of maple & walnut sandwiched between 2 layers of veneer . The outside of the...
  14. J

    cancer awareness ribbon feature ring

    Hi Everyone: Attached is what I came up with for my cancer awareness feature ring. In my opinion it came out deecent. I must cofess somehow I managed to get the feature ring out of round about 3/16".
  15. J

    teak

    Hello: I might be able to get some teak lumber at a real good price. Has anyone ever used it for turning? If so what are your comments? Thanks...................
  16. J

    laser guide

    Hi Loyd: I saw somewhere you demonstrated a laser saw guide for cutting 2 nd,3rd and so on generations. I can't find it again. Could you direct me to it ? Thanks...........
  17. J

    Hello

    Hi Tim.... Thanks
  18. J

    Hello

    My name is AL. A little about myself. I'm semi retired from self employed for about 30 years. been doing woodworking & wood turning for about 10 or 12 years as a hobby. My first introduction to woodworkin & woodturning was in the 60's in High school shop. I've just recently started segmented...
Back
Top