• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. Ed Cuttle

    lloyd, i had to get a new compute as my hard drive failed how can i get the software down...

    lloyd, i had to get a new compute as my hard drive failed how can i get the software down loaded to my new machine? i will try and download it again? thanks for your help, ed
  2. Ed Cuttle

    Version 1.1.010

    Lloyd, when I am in the Summary, and every time I move a column to a different location and select Print Preview, Segment PRO gets an error If I just select Print, it is ok
  3. Ed Cuttle

    01 - Introducing Segment PRO!

    Bob, I am having the same issue, lots of scrolling. I have tried to adjust my resolution but no success yet.
  4. Ed Cuttle

    01 - Introducing Segment PRO!

    Great video, great product. Looking forward to adding this new piece to my suite!
  5. Feature Ring Vase

    Feature Ring Vase

    Segmented Vase with a mix of pieces per ring. 24 and 12 segments per ring with a simple feature ring. Maple, Bubinga, Ash and Wenge with various died disks 344 Pieces
  6. 24 Segment Vase

    24 Segment Vase

    Segmented Vase with 24 segments per ring. Mini Feature ring on top neck of 48 segments. 627 Pieces - Avodira and Paduk
  7. Ed Cuttle

    Lamination Pro Circles

    Downloads button Lloyd, how / where is the 'Downloads' button so I can get the new version? Thanks, Ed
  8. Ed Cuttle

    Stave Segment Techniques

    Lloyd, having one problem. Now that I have a test design (a vase), my one ring that I have as a compound ring shows a desired compound slope of 75 degrees (ring #3) and not sure that my table saw will go high enough to do the cut for the board width. What do you do when this happens? Also...
  9. Ed Cuttle

    Stave Segment Techniques

    Lloyd, completed the MDF test and I must say, the segments matched perfect! What is your recommendation to mount the ring so you can even the bottom/top. I have seen some folks hot glue the ring to a faceplate MDF.
  10. Ed Cuttle

    Stave Segment Techniques

    Again, thanks for the clarification, that makes more sense to me now. And I will take you up on the idea to run a test w/MDF. Will keep you posted, Ed.
  11. Ed Cuttle

    Stave Segment Techniques

    Again, Thanks Lloyd, I went and changed the two rings from Stave to Compound, and made some adjustments. Woodturner Pro defaulted to 40 degrees for the 'Desired Compound Slope' which will be supported by the 'Wedge' I will create as you mentioned earlier, correct? So in the Cutting Summary...
  12. Ed Cuttle

    Stave Segment Techniques

    Thanks for that insight Lloyd, I will give it a try. And I would guess that if I need a slope other than 40, or 50, just make another wedge to use on the miter fence for that degree. In my Woodturner Pro .wtp design, I have a stave segment ring that has a miter angle of 5.33 deg and blade tilt...
  13. Ed Cuttle

    Stave Segment Techniques

    Was wondering what folks use to cut stave segments. Also, is there a plan somewhere to build a jig for the table saw, or do most use the bandsaw or compound miter saw? Would really like to try building a stave vase, but any info would be appreciated. Thanks in advance! Ed
  14. Ed Cuttle

    Segment jig

    I would agree with Dick, I too glue one ring at a time and have always had luck with this method. Even one at a time you do need to insure that the new glued ring does not move on you. And after 3 or so, I do 'rough turn' the rings. This has helped me and also helps on keeping the mass from...
  15. Ed Cuttle

    Exporting LaminationPro SW designs to WTP

    Hi Billy Make sure you have WTP up and running, then the export button should be active. Ed
  16. Segment Stomper Open 18 Segment

    Segment Stomper Open 18 Segment

    First open segment project using the template and segment stomper. Learned a lot during the process. Design from 3D Design and Woodturner Pro. Make sure you give yourself enough glue up surface! Ed Cuttle
  17. Ed Cuttle

    Open Segment process

    Hey Lloyd, all GREAT ideas! Makes sense on not touching that last ring. So, back to the shop and will keep you posted! Thanks again and will see how John does as well. Ed PS in Huntley Il, and here comes our first snowfall in 292 days!
  18. Ed Cuttle

    Open Segment process

    Well, I have started on my first open segment vase. Normally, when I build a normal segment vase/bowl, I will rough turn both inside and outside after gluing up a couple rings, then continue this process. So I started this open segment vase, and after the base and 4 segments glued up, I turned...
  19. Ed Cuttle

    Open Segment process

    Hi Lloyd Just received the Segment Stomper and SegEasy plates. Will work on getting things setup this week. When you glue up each ring, what technique do you use to avoid glue squeezing into the open segment sides, do you sand each open segment after glue up to the next ring, and then, as I...
Back
Top