• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. E

    Returning after 4 year hiatus, need help

    I started entering the world of segmented turning about 4 years and had some limited success using this software and producing bowls. But then I ventured off into other woodworking paths, mainly Intarsia. But I recently retired and have more time and would like to venture back into this realm...
  2. E

    Requesting clarification on a setting in LaminationPro

    It has been almost a year since I last did any segmented turning and using this software. The last two attempts of making a feature ring segmented bowl were a bit disappointing. The accuracy of my cuts and or general assembly resulted in a repeating pattern that was not correct. The effect was...
  3. E

    First feature ring bowl. Looks nice at first but has many pattern flaws

    I have finally made a bowl with a southwest design feature ring but I am disappointed in the results. At first glance it looks decent but if you actually look at the feature ring the flaws are glaring. The few people I showed it too at first glance thought it was great. My son took one look...
  4. E

    Issues with cutting small segments on table saw catching blade

    I think i know what is happening here but several times when I am cutting small segments on my table saw setup Title: Imgur the piece will catch the sawblade and blast away violently. I assume the problem is that the workpiece is not supported by the table saw base but instead is raised up a...
  5. E

    Still having issues with cutting consistent thin strips on table saw

    I have tried a couple of times to make this laminate pattern from thin (like 1/8 inch) strips of ripped wood but I am still having obvious tapering issues from end to end. The total length of the strips are about 3 feet in this case. As you know you first you cut a series of strips of various...
  6. E

    How accurate or precise must my table saw be for feature rings

    I tried to make a feature ring (eventually for WoodturnerPro) using a design from LaminationPro. But as I cut the strips on my portable contractors table saw and then glued them together it became quite obvious something was amiss. It you look at the pictures in the link below it will be...
  7. E

    struggling to get correct results in LaminationPro and WoodturnerPro

    I am struggling with getting precision results using LaminationPro and WoodturnerPro. I have made a couple of practice runs but still cannot get the results to match what I build. I am trying to use LaminationPro to produce a 'feature ring' to be used in WoodturnerPro. But some of my problems...
  8. E

    LaminationPro not saving all settings to file

    I have noticed that when you configure settings in the Southwest view such as Strip Width, Center Strip, Strips, and Export region size that these settings are not saved to the .lam file. Thus upon exit and reload of this saved file these 4 settings are not reloaded. This should be an easy...
  9. E

    How to measure first cut width

    I have a simple question. In Laminate Pro there is a key setting for First Cut Width. Is that a measurement parallel to the long side of the laminate strip or is it perpendicular to the angle cut across the strip? Hopefully this picture will explain to the two interpretations of that number...
  10. E

    Missing kerf option in Laminate Pro

    I am new to these tools but in reading the help for Laminate Pro it talks about the option to show kerfs. But the software I have it not showing that option. Title: Imgur Title: Imgur I know that software changes over time with new revisions. However the help supplied with this version states...
  11. E

    New member from Ohio

    I just started woodworking about 16 months ago, mostly with flat scrollsaw work. Then around 6 months ago I bought my first lathe and have been ramping up the learning curve with a strong interest in segmented bowls. I have made 1 segmented bowl so far and hope to learn how to use the Segment...
Back
Top