• Are you looking for a coupon code to buy my software? You can get one from lots of 3rd party sites but they won't work. My software never goes on sale and has never been discounted. The only coupon codes that are given is when I give a club presentation and I offer a discount to the attendees. Other than that, everyone pays the same price.

Search results

  1. mfisher

    Storyboard Top Row is a solid disk not working

    SP version 1.1.029 Bowl Settings: Featured Ring, 12 Segments Storyboard: Top Row, Base Row, and Accent Row selection (selected Top Row is a solid disk) In Storyboard, when selecting Top Row is a solid disk, the storyboard image shows the change. Going back to Return to bowl view, the solid...
  2. mfisher

    Anthony questions using LP and SP.

    http://woodturnerpro.com/community/index.php?threads/985/post-10721 Sinister1957 post 3 I see the thickness which is the height and the length and I understand that ..when creating the feature ring do I use the with width as per segmentpro table suggest ... or is there a setting I missed in...
  3. mfisher

    WTP Summary Species limit

    Up until this month I never used more than 4 or 5 species of wood in WTP, The summary sheet printed the correct amount of each species per ring. This week I was designing a vessel with 6 species of wood. The painting was no problem. Ring view showed the different species in the correct...
  4. mfisher

    Add SP to Software Support forum

    Lloyd. I would like to recommend adding SP to the Software Support section. Then all four software would be listed. Mike
  5. mfisher

    Wood selection advice

    Most of my work has been done using maple, walnut, mahogany, mesquite and cedar. For my next solid segment project I would like to introduce some different color. I am looking at using some Padauk, but read that it can "bleed" color into the lighter color wood next to it. Read that Bloodwood...
  6. mfisher

    possible math issue on summary view

    Lloyd, I was playing with Tom's free bowl plan. I noticed something interesting. Here is what I did. - Started SP - Load Tom's saved plan - Changed profile to a different bowl design. SP converted the design over in the bowl view just fine. - instead of 48...
  7. mfisher

    SP Summary export to CSV for excel

    Lloyd Is there a way to export the summary view into Excel using SP? I know that WTP has a feature that exports the cut summary as a csv file. Reason I am asking is some of the profiles in SP would be great for a bowl from a board type concept. Similar to what I did with my SW dizzy bowl...
  8. mfisher

    Rob S. Using LP in WTP question.

    Robert Sjulstad Hi Everybody! Rob Sjulstad, Sun City, AZ asking for help. I have already designed and constructed a SW Feature Ring in Lamination Pro (8 Repeats @ 3" each, height is 2.625 +/- ,depending on where I decide to cut off the peaks or whatever the pointed tops and bottoms are called. I...
  9. mfisher

    Lamination Pro 3.2.008

    Lloyd. I saw that there was a new build for lamination pro 3.2.008. I downloaded the install file and ran the program. The install when fine and the program seems to be running fine. After the install, Lamination Pro shows the build is 3.2.007, when the download page shows the current build...
  10. mfisher

    SW Dizzy Bowl

    Here is my WTP plan for the SW Dizzy Bowl. Please note while the plan shows rings 3 through 37 as segmented rings. The rings are cut from a blank. If I used "disk" , you only get the OD (outside diameter). By selecting "flat", you can get both the OD and ID (inside diameter). These...
  11. mfisher

    Ring Bowl

    This is a take off of a bowl made from rings by Dennis Edwards with a segmented ring top. I like sw designs. The ring blank was made up of walnut, maple, zebra wood, bloodwood, chakte-kok. 2 8x8x4" blanks were made. the blanks were then cut into 1/8 thick slabs. I designed the bowl using...
  12. mfisher

    Cross Bowl

    The cross bowl consists of 229 pieces of maple, walnut, mesquite, and cedar. The bowl is 3 ¾ inches tall and 8 ¼ in diameter. The accent between the crosses is made up of maple and cedar The bowl was finished with six coats of sanding sealer and four coats of wipe on gloss poly. Comments...
  13. mfisher

    Transition zig zag bowl

    This bowl is 6 inches in diameter. The bottom and top is made from solid mesquite. The featured zig zag is maple and walnut. I added turquoise inlace as a highlight to the featured ring. Finish was with 3 coats of sanding sealer, then finished with wipe on gloss poly. I recently have...
  14. mfisher

    Lamination Pro - Southwest Pattern print preview

    Not sure this is the proper place for this thread. for a comment on Lamination Pro southwest pattern. In the print preview the following is created. "To make the 1st. Generation. cut the laminate board ...... To create the SW design, make a center kerf that is (X) wide Make (Y) strips...
  15. mfisher

    New member from Arizona (sun city wests and payson)

    Hi. I have been lurking on woodturner Pro for a year or so. Finally decided to join. I started doing segmented bowls a year ago. I really like the work of Ray Allen (southwest designs) and others who have done landscape scenes for their featured ring. Prior to that I was into making bandsaw...
Back
Top